| 01:24.25 | *** join/#tuxscreen Sammy (~sam@210.241.233.74) |
| 01:30.13 | *** join/#tuxscreen rabbi_ilya (~ilya@user-10cm1uv.cable.mindspring.com) |
| 01:30.23 | rabbi_ilya | hello |
| 02:08.43 | *** join/#tuxscreen Evanrude (~david@cdm-197-152.tca.net) |
| 02:49.05 | *** join/#tuxscreen gatofisch (~trillian@eastquad-170-211.reshall.umich.edu) |
| 07:22.18 | Sammy | can any guru give me some hint to set up the CF ethernet card ? |
| 07:23.26 | Sammy | why cardmgr don't know what it is ? |
| 07:24.27 | Sammy | my card is PRETEC CompactLAN , and it's NE2000 compatible ... |
| 08:18.15 | *** mode/#TuxScreen [+o TimRiker] by ChanServ |
| 08:40.29 | *** join/#tuxscreen ibot (ibot@rikers.org) |
| 08:40.29 | *** topic/#tuxscreen is we are moving to #eLinux for general Embedded Linux | http://TuxScreen.net/ | Linux on your phone! | no TuxScreens and no JTAGs | gcc-final fails in current buildroot "ln -s `pwd`/build/stage/lib/* build/stage/arm-linux/lib/" | tinyx builds again |
| 08:40.29 | *** mode/#TuxScreen [+o ibot] by ChanServ |
| 09:20.24 | TimRiker | Sammy: on the Tux? what does cardctl ident say? Are you sure it's a 3.3v card? does the log show a module being loaded? |
| 10:00.22 | *** join/#tuxscreen mallum (~mallum@pc-80-193-218-21-hw.blueyonder.co.uk) |
| 10:33.08 | *** join/#tuxscreen Sammy (~sam@210.241.233.74) |
| 10:33.23 | Sammy | Tim: YES I use the 3.3v card , and cardctl say |
| 10:34.30 | Sammy | product info: "PERTEC" "Ethernet CompactLAN 10BASET 3.3v","980918,"Rev.A" |
| 10:34.43 | Sammy | function: 6 (network) |
| 10:35.29 | Sammy | and |
| 10:36.00 | Sammy | no, it's can't find out the device to load |
| 10:39.34 | Sammy | ant idea ? |
| 10:39.44 | Sammy | err any |
| 10:45.23 | TimRiker | /etc/pcmcia/config needs to have an entry for your card. then it loads the module listed there. |
| 11:00.33 | Sammy | but it already have |
| 11:01.01 | Sammy | card "PRETEC CompactLAN Ethernet" |
| 11:01.41 | Sammy | version "PRETEC", " Ethernet CompactLAN 10baseT 3.3v" |
| 11:01.53 | Sammy | bind "pcnet_cs" |
| 11:14.43 | Sammy | strang , but this card can detect by ipaq on familier 5 |
| 11:17.21 | TimRiker | case is different... 10BASET 10baseT |
| 11:17.59 | TimRiker | is cardmgr running? |
| 11:18.32 | Sammy | yeap |
| 11:18.50 | TimRiker | try changing the case and restarting cardmgr. |
| 11:19.20 | TimRiker | log does not show cardmgr trying to load the module? |
| 11:20.49 | Sammy | sorry that's my mistake , it's PRETEC CompactLAN 10BaseT 3.3V |
| 11:21.21 | Sammy | because I type what I saw from tux |
| 11:21.46 | Sammy | my minicom was taken by ipaq |
| 11:22.46 | Sammy | here is ipaq's log: |
| 11:22.52 | Sammy | card "ide0: unexpected interrupt, status=0x00, count=24 |
| 11:22.53 | Sammy | cardmgr[82]: socket 0: PRETEC CompactLAN 10BaseT 3.3V" |
| 11:22.54 | Sammy | cardmgr[82]: executing: 'modprobe 8390' |
| 11:22.55 | Sammy | cardmgr[82]: executing: 'modprobe pcnet_cs' |
| 11:22.56 | Sammy | eth0: NE2000 Compatible: io 0xc29a0320, irq 42, hw_addr 00:20:CB:FF:0A:66 |
| 11:23.15 | TimRiker | ah, then it is trying the module so /etc/pcmcia/config is working. |
| 11:23.38 | TimRiker | oh, that's the ipaq... |
| 11:23.57 | TimRiker | and on the tux you get nothing from cardmgr? |
| 11:24.06 | Sammy | yeap |
| 11:24.32 | TimRiker | sa1100cs is loaded? |
| 11:25.10 | Sammy | oh , have few lines from driver |
| 11:25.12 | TimRiker | should have pcmcia_core sa1100_cs and ds all loaded. |
| 11:25.29 | TimRiker | then run cardmgr and insert the card. |
| 11:26.26 | Sammy | release cardmgr and restart that ? |
| 11:26.58 | Sammy | because cardmgr was already run |
| 11:27.46 | Sammy | and I insert the card it's only show up three line : |
| 11:28.15 | Sammy | shannon_pcmcia_configure_socket(): warning, can't perform reset |
| 11:28.31 | Sammy | three times |
| 11:29.48 | Sammy | and cardctl status find the card at socket 0 |
| 11:34.44 | Sammy | what a stupid I am |
| 11:36.18 | Sammy | there is just a single character doesn't match |
| 11:37.19 | Sammy | 10BaseT and 10baseT , is not the same ....ha |
| 11:43.09 | Sammy | btw , thanks TimRiker |
| 12:01.28 | TimRiker | did it work when you changed it? |
| 12:02.12 | TimRiker | I gotta sleep. you do need to stop/start cardmgr to pick up changes to /etc/pcmcia/config |
| 12:02.13 | TimRiker | nite |
| 12:03.36 | Sammy | yeap , it's work now .. |
| 12:03.47 | Sammy | nite all |
| 21:02.42 | *** join/#tuxscreen TimRiker (timr@rikers.org) |
| 21:02.43 | *** mode/#TuxScreen [+o TimRiker] by ChanServ |
| 21:55.21 | *** join/#tuxscreen mallum (~mallum@pc-80-193-218-21-hw.blueyonder.co.uk) |