| 00:00:14 | sjm | hi all |
| 00:01:05 | sjm | BZFlag: the microwin stuff is ready to go, but I don't have write access to download/microwin/latest :( |
| 00:02:01 | BZFlag | sjm: what about the main mw site? does what we have differ a lot from what is on thier cvs? |
| 00:02:29 | BZFlag | I'd much rather see us using thier stuff with the smallest patches we can muster. |
| 00:04:04 | sjm | BZFlag: hmm... I orgignally diffed my tree against their 0.89pre8 release, and there were significant changes. The patch was something like 700k from an 8M archive. |
| 00:05:13 | sjm | But I have a working tree available that's 1.3M zipped, and integrates fine into buildroot |
| 00:09:00 | BZFlag | what is your tree based on then? |
| 00:09:50 | sjm | the tree alex holden posted to the list |
| 00:12:00 | BZFlag | I'd really like to get in sync with the main tree if possible. feel free to just drop the tarball in download with some long name like microwindows-20020412-tuxhack.tar.gz though. |
| 00:12:40 | BZFlag | you have it using jpeg as a shared library I presume? |
| 00:12:44 | sjm | hehe, it's already calledmicrowin-sjm-020412.tar.bz2 |
| 00:12:52 | sjm | yep |
| 00:13:12 | BZFlag | I'd prefer fill dates if you don't mind. the rest is fine. |
| 00:13:16 | BZFlag | er full |
| 00:13:39 | sjm | k |
| 00:25:48 | andersee | evening all |
| 00:26:04 | andersee | yawns and streches |
| 00:31:00 | jacques_gone | hi andersee |
| 00:55:52 | andersee | hi jacques |
| 03:23:13 | Error403 | time to test out my 5v PCMCIA slot ;) |
| 03:25:33 | Error403 | damn |
| 03:25:35 | Error403 | didn't work :( |
| 03:26:01 | Error403 | my soltering iron really sucks |
| 03:27:48 | Error403 | great, 3.3v don't work anymore either :/ |
| 03:41:57 | TomW | yawn! |
| 04:11:45 | Error403 | yay |
| 04:11:56 | Error403 | recovered 3.3v and got one of my slots to be 5v :D |
| 04:15:09 | Error403 | heh! |
| 04:15:11 | Error403 | ssh works ;) |
| 04:50:56 | Error403 | BZFlag: hey |
| 04:51:00 | Error403 | BZFlag: Got a second? |
| 04:51:28 | Error403 | err |
| 04:52:56 | Error403 | BZFlag: is it possible that increasing the voltage on the tuxscreen (on just one of the PCMCIA slots) would make it unstable? Because for some reason this kernel is quite unstable |
| 04:53:03 | Error403 | it is crashing and won't load half the time |
| 04:53:20 | Error403 | and it's telling me that my Vcc is wrong for only one of my NIC |
| 04:53:27 | Error403 | 3c589_cs: RequestConfiguration: Bad Vcc |
| 04:54:00 | TomW | Error403: check the voltage on the 3.3 supply, you may have the +5 shorted to the 3.3 |
| 04:54:30 | TomW | Error403: Not only will the processor become unstable, but you can seriously damage chips that way. |
| 04:55:05 | Error403 | where's the 3.3 supply? |
| 04:55:46 | TomW | Error403: Better to shut the supply off, then check to see if the supplies are shorted with an Ohmmeter. Always a good practice, buzz the connections out before applying power, then sit back for a few minutes to review what you just wired up, THEN apply the power. |
| 04:56:17 | TomW | You have to be able to read the schematics to locate where the 3.3 supply is, it is clearly marked on the schematics. |
| 04:56:18 | Error403 | buzz them out? |
| 04:57:08 | TomW | Yup, most Ohmmeters have a buzzer or Pizeo beeper in them to tell you when you touch the two leads together. |
| 04:57:27 | Error403 | mine doesn't |
| 04:57:29 | Error403 | just shows it |
| 05:00:12 | Error403 | to be honest, I don't see anything that says anything about 3.3v anything |
| 05:00:33 | TomW | Error403: look at the supplies to the Integrated Circuits. |
| 05:01:08 | Error403 | ahh |
| 05:01:10 | | those are the biggest knockers I have EVER seen! |
| 05:01:10 | Error403 | where are those? |
| 05:03:44 | andersee | ibot is a pervert |
| 05:03:57 | andersee | ;-) |
| 05:04:00 | Error403 | :) |
| 05:05:05 | TomW | andersee: shame, you'll stunt ibot's emotional development.. |
| 05:05:17 | TomW | andersee: ;-) |
| 05:05:19 | Error403 | hmm |
| 05:06:12 | Error403 | not seeing these IC sheets |
| 05:06:29 | Error403 | http://www.tuxscreen.net/wiki/view/Main/ScheMatics |
| 05:06:31 | Error403 | I'm there right now :/ |
| 05:11:27 | Error403 | ok, I figure out what I did wrong |
| 05:12:05 | Error403 | TomW: As I understand you don't have to enable 5v on both slots, so I just did it on R227 |
| 05:12:06 | Error403 | errr |
| 05:12:08 | Error403 | R337 |
| 05:12:46 | Error403 | TomW: But looking in the picture http://www.tuxscreen.net/download/schematics/5Vx2.jpg, I don't understand the deal is with the items circled in blue |
| 05:15:02 | TomW | did you remove R338 & R337? |
| 05:15:42 | Error403 | no |
| 05:15:45 | Error403 | jusr R337 |
| 05:16:04 | Error403 | R338 is if you want 5v on the bottom slot, no? |
| 05:23:19 | TomW | Yeah, remove R338, then jumper first & third pins on J600 to have bottom slot full time +5v. That's the way I read it from the picture. |
| 05:24:42 | Error403 | well, I have already remove R337, and I really don't want the bottom slot to be 5v because it's very hard for me to do this |
| 05:25:37 | Error403 | well, whatever |
| 05:25:46 | Error403 | might as well go all out in order to do it right |
| 05:30:10 | TomW | Error403: Older PCMCIA cards were +5, the newer cards are 3.3 |
| 05:30:38 | Error403 | all of mine are 3.3v |
| 05:30:45 | Error403 | will 3.3 not work in 5? |
| 05:31:57 | Error403 | errr |
| 05:32:06 | Error403 | all of mine are 5v, I mean :) |
| 05:32:22 | TomW | No, if it is a 3.3 volt card, then it won't work at +5, you will probably damage (destroy) the card by running it at the higher voltage. |
| 05:32:55 | Error403 | I meant to say that all of mine are 5v :/ |
| 05:33:39 | Error403 | so I shouldn't make both of my slots 5v |
| 05:33:41 | Error403 | just one, right? |
| 05:33:49 | TomW | Error403: Then jumper the pin3 to the section shown in yellow. |
| 05:33:51 | Error403 | that makes more sense |
| 05:34:06 | Error403 | okay, and what about pin 1? |
| 05:34:14 | Error403 | jumper that to 3? |
| 05:34:17 | TomW | that is the 3.3 supply. |
| 05:34:32 | Error403 | okay.... |
| 05:34:35 | BZFlag | andersee: I changed the default ash prompt cause it was bugging me. |
| 05:34:47 | TomW | Do you have any friends who know electronics? |
| 05:35:06 | Error403 | TomW: no, but I don't see how understanding electronics is going to help me much |
| 05:35:15 | TomW | Oh? No? |
| 05:35:17 | Error403 | I just want to make *one* slot 5v, not both |
| 05:35:34 | Error403 | and I just need to know a couple things |
| 05:35:46 | Error403 | C400->pin 3 |
| 05:35:51 | Error403 | and remove R337 |
| 05:35:53 | Error403 | is that it? |
| 05:36:03 | Error403 | Do I want to do pin 1->pin 3? |
| 05:36:40 | TomW | You can do some real damage to the Tux electronics if you don't know what you are doing. Most of tha schematic & mod info is for experienced electronics techs to refer to . It was never meant for a someone who doesn't know electronics to follow. |
| 05:37:04 | Error403 | well my tux is a paper weight anyways then |
| 05:37:08 | Error403 | so either way you slice it |
| 05:42:52 | TomW | Anyone know more about the IDE interface spec than I do? I am puzzling over some of the sig defs. |
| 05:43:54 | TomW | specifically: CSEL, PDIAG, and DASP. |
| 05:47:00 | TomW | Ahh. Found it, at Apple.com of all places. |
| 05:58:16 | andersee | BZFlag: patch looks ok. I think I'll backport it for 0.60.3 |
| 06:00:46 | BZFlag | yeah. size is a wash if you include the required features anyway. |
| 06:01:11 | BZFlag | it probably saves a few bytes. ;-) |
| 06:03:35 | andersee | BZFlag: I'm gonna try valiantly to get 0.60.3 ready tonight. |
| 06:04:11 | andersee | BZFlag: HowNow that I have the config system in the devel branch w |
| 06:04:45 | andersee | BZFlag: err. Howd you like the new config system. Now that I have the config system in the devel branch working, I'm anxious to kill off the 0.60.x tree |
| 06:07:56 | BZFlag | there's no help yet |
| 06:08:45 | andersee | true.... |
| 06:08:56 | andersee | smells a volunteer... :-) |
| 06:09:04 | TomW | heh. |
| 06:09:07 | BZFlag | well, for many options anyway. ;-) |
| 06:09:26 | andersee | Builds much faster now though |
| 06:09:28 | Error403 | TomW: How are students suppose to learn if teachers don't want to teach? |
| 06:09:31 | BZFlag | agreed |
| 06:10:45 | andersee | BZFlag: I like the fact I can now cd into a subdir, work on something, and just run 'make' and it works properly in the subdir.... |
| 06:10:59 | andersee | BZFlag: Without that, I _hated_ working on the devel tree |
| 06:15:45 | BZFlag | ooh. nice I had not noticed that. |
| 06:17:23 | andersee | BZFlag: That was one of the biggest reasons the 0.60.x tree has lingered around so long... ;-) |
| 06:20:29 | pmisfit | is away: whoops... pmisfit interruptus |
| 06:20:34 | pmisfit | is back (gone 00:00:06) |
| 06:20:43 | pmisfit | wow that was weird. |
| 06:21:19 | pmisfit | BZFlag: i noticed you used CONFIG_FPE_NWFPE instead of CONFIG_FPE_FASTFPE in the new kernel config |
| 06:21:33 | pmisfit | BZFlag: does ppp require this? |
| 06:23:12 | BZFlag | andersee: what's with the Makefile.in and Makefile? are both staying? I assumed you would nuke all the Makefile files when you added the .in |
| 06:24:14 | BZFlag | pmisfit: nope, just that NWFPE is more stable and folks don't seem to be hacking the kernel so much as wanting real apps to work now. |
| 06:24:33 | andersee | Both are indeed staying! Pick a dir and take a close look! |
| 06:25:19 | BZFlag | then yout .in are not really going to be automake files, just includes? |
| 06:25:23 | BZFlag | er your. |
| 06:25:30 | BZFlag | perhaps another name would be better? |
| 06:25:36 | andersee | The Makefile is a little stub to run the contents of Makefile.in standalone. Makefile.in does the heavy lifting with some help from the top level Rules.mak |
| 06:26:25 | pmisfit | BZFlag: thanks |
| 06:30:48 | BZFlag | andersee: I would have done like shell/shell.mk instead. |
| 06:30:58 | Error403 | whatever |
| 06:31:11 | Error403 | I guess I'm down a slot until someone wants to tell me what I should be doing |
| 06:31:34 | BZFlag | Error403: you undid your mod? is the box stable again? |
| 06:31:50 | Error403 | I didn't really undo it |
| 06:31:52 | Error403 | you can't |
| 06:32:03 | Error403 | once you remove the resistor, I'm assuming you can't go back |
| 06:32:06 | BZFlag | is the box stable again? |
| 06:32:10 | Error403 | yes |
| 06:32:35 | Error403 | I've completely fucked up the circuit board |
| 06:32:51 | Error403 | since the soltering irons I have suck |
| 06:34:01 | Error403 | At the end I finally resorted to not using solter and just taking a wire and poking it into the top of the J600 |
| 06:34:02 | BZFlag | which slot are you modding and which resistor did you remove |
| 06:34:17 | Error403 | the top slot, and I removed R337 |
| 06:34:45 | Error403 | I connected the left contact of C400 to Pin 3 (left side) of J600 |
| 06:35:53 | BZFlag | http://TuxScreen.net/wiki/view/PCMCIA-5V <- you wanted to connect the point by |
| 06:36:24 | Error403 | Do I want to connect Pin 1->Pin 3 of J600? |
| 06:36:38 | BZFlag | the label "C400" (not a pin on C400) to where the right side of the resistor was which is J600 pin 5 |
| 06:37:18 | Error403 | BZFlag: Are you sure that the right side of C400 is different from the lefT? |
| 06:37:24 | Error403 | http://www.xmission.com/~redbeard/tuxscreen-5v-pcmcia-hack/ts_workarea-done-lg.jpg |
| 06:37:45 | Error403 | Check that out, it looks like the solter had leaked onto both contacts and andersee said it works fine for him |
| 06:37:58 | Error403 | andersee: Am I correct that it's just one big wad of solter? |
| 06:38:14 | BZFlag | R337 right side was connected to pin 5, not pin 3 (left side was pin 3, but don't mess with that) |
| 06:39:10 | BZFlag | C400 is that cylinder thing standing up. you are not connecting to any of it's pins. |
| 06:39:30 | Error403 | ohh |
| 06:39:31 | Error403 | no |
| 06:39:37 | Error403 | I didn't know that's what C400 was :/ |
| 06:40:19 | Error403 | I'm connecting a wire from the right of resistors 452 and 453 |
| 06:40:36 | BZFlag | correct. to where? |
| 06:40:53 | Error403 | but the first hole, not the second (the second hole is the one closer to the C400 label) |
| 06:41:02 | Error403 | to pin 3 on the left side of J600 |
| 06:41:21 | BZFlag | pin 3 is the one right below pin 1. that's not what you want |
| 06:41:33 | BZFlag | pin 5 is two down from 1 |
| 06:41:37 | Error403 | ohh |
| 06:41:42 | Error403 | sorry, yes, was reading it wrong |
| 06:41:43 | BZFlag | where the picture shows. |
| 06:41:49 | Error403 | it's pin 5, sorry |
| 06:42:08 | Error403 | I've connected it to Pin 5 |
| 06:42:51 | BZFlag | so remove any cards, break the reistor, confirm that there is no contact between pin 5 and pin 3, then add you jumper from up by the right of R452 to pin 5 |
| 06:43:32 | BZFlag | and then do not insert any 3.3v cards in the top slot ;-) |
| 06:43:59 | BZFlag | is that how you are now? |
| 06:44:28 | Error403 | yes |
| 06:44:46 | Error403 | hrm |
| 06:44:52 | BZFlag | any the box is stable? then are there any issues or is all well with the top slot? |
| 06:45:26 | Error403 | any the box is stable? |
| 06:46:14 | BZFlag | and.. |
| 06:47:10 | Error403 | no, it's not stable |
| 06:47:16 | Error403 | that's how I've had it for the last hour |
| 06:48:18 | BZFlag | <BZFlag> is the box stable again? |
| 06:48:18 | BZFlag | <Error403> yes |
| 06:48:25 | BZFlag | explain? |
| 06:48:45 | Error403 | well, without the PCMCIA card in it is |
| 06:48:51 | Error403 | with it in it is unstable |
| 06:49:04 | Error403 | I think the main problem is that I can't use solder |
| 06:49:17 | Error403 | and there's poor or no contact at all |
| 06:49:50 | BZFlag | sounds about right. ;-) find someone that can and have it fixed. I can't help with that remotely. |
| 06:50:23 | Error403 | find someone? heh |
| 06:50:24 | Error403 | hrm |
| 06:50:36 | Error403 | I guess I'll just have to take another stab at soldering it |
| 06:50:50 | Error403 | It wouldn't be a problem if I had some money |
| 06:51:13 | Error403 | Otherwise I'd go out and buy a new sodering gun |
| 06:51:19 | BZFlag | no NOT connect pin 1 to pin 5 if pin 5 is connected to anywhere else. |
| 06:51:37 | Error403 | Okay, I haven't |
| 06:51:55 | BZFlag | soldering gun == big thing with a trigger == not what you want. |
| 06:52:05 | Error403 | But what does it do if you have Pin 1->pin 5 connected? |
| 06:52:07 | andersee | BZFlag: Seems we should take redbeard's pics and annotate them properly.... |
| 06:52:13 | BZFlag | soldering iron == small pencil shaped thing == what you want. |
| 06:52:27 | Error403 | Yeah, I have a regular iron, but the tip of it never gets hot |
| 06:52:36 | andersee | With the smallet point you can get... |
| 06:52:56 | BZFlag | Error403: pin 1 has 3.3v, the right of R452 has 5v |
| 06:53:01 | Error403 | I want a metalic pen |
| 06:53:14 | Error403 | the stuff that lets you "write" solder on :) |
| 06:53:35 | BZFlag | the picture on http://TuxScreen.net/wiki/view/PCMCIA-5V has a _diode_ between them NOT a wire. |
| 06:54:03 | Error403 | yeah, I didn't put a wire on the two, ever |
| 06:54:33 | BZFlag | so when the switch to 5v is open, the circuit gets 3.3v from pin 1, and when the switch is closed, the diode blocks the 5v from flowing back to pin 1 |
| 06:55:06 | BZFlag | that's what a diode does. only allows current flow in one direction. |
| 06:56:39 | andersee | BZFlag: We _really_ should replace that pic, minus the confusing diodes... |
| 06:57:18 | pmisfit | may i suggest: http://www.mtechnologies.com/building/atoz.htm |
| 06:58:24 | BZFlag | pmisfit: heh |
| 06:59:31 | BZFlag | andersee: agreed. we need a picture with just the wire jumpers |
| 07:00:05 | BZFlag | and a picture with a three way switch. and the diode should just be written out for those that understand. |
| 07:00:23 | BZFlag | well, must sleep sometime. |
| 07:02:19 | andersee | night |
| 07:30:13 | cbiffle | I have a question regarding the codec/modem chip in the Shannon. Any takers? |
| 07:34:00 | cbiffle | A lot of lurking tonight. :-) |
| 08:09:21 | pmisfit | cbiffle: a lot of *sleeping* tonight... i'm next... |
| 08:10:05 | TomW | Yeah, the autorouter has made me a happy hacker tonite. |
| 08:10:16 | pmisfit | is away: zzzzzzzz |
| 08:10:18 | TomW | maybe it *is* time to quit? |
| 19:51:41 | scanline | is away: I'm busy |
| 19:51:54 | scanline | is back (gone 00:00:03) |
| 19:52:18 | scanline | hehe.. didn't have desk space for my Tuxscreen so I finally realize I can hang it where the standard phone usually go |
| 19:53:26 | scanline | s/go/goes/ |
| 19:53:32 | scanline | Just need a longer ethernet cable... |
| 19:53:45 | scanline | thinks ickysneeze ran away with his bag of crimps :( |
| 20:24:40 | Error403 | lo lo |
| 20:25:10 | Error403 | BZFlag: You'll be glad to know that I went out and bought a new soltering iron, worked great. I soltered the wire on right away |
| 20:25:16 | Error403 | BZFlag: Seems the box is stable so far |
| 21:15:37 | scanline | decides to hack on buildroot's picogui support some |
| 21:28:54 | BZFlag | Error403: have you tried different 5v cards? |
| 21:29:00 | Error403 | yes |
| 21:29:10 | BZFlag | scanline: it builds and runs, it just needs new ts code. |
| 21:29:23 | Error403 | BZFlag: the driver for my 3com card says "bad Vcc" and won't load the driver |
| 21:29:27 | Error403 | so I'm not sure what's going on |
| 21:29:30 | scanline | BZFlag: ok, good. I'm compiling buildroot at the moment, I haven't used it in a while |
| 21:29:31 | BZFlag | Error403: hmm. perhaps you need to mod the kernel so that it knows the slot is 5v |
| 21:29:43 | Error403 | BZFlag: it's the kernel you sent me |
| 21:29:52 | BZFlag | make;make picogui;make should be all you need. |
| 21:29:57 | scanline | BZFlag: plus i'd like to update it with some of the new picogui developments, like the nifty dithering :) |
| 21:29:58 | scanline | ok |
| 21:30:30 | Error403 | BZFlag: Are you suggesting that the patches for the shannon specificly disable 5v cards? |
| 21:30:42 | Error403 | BZFlag: And in order to turn 5v back on I'd have to hack up the source? |
| 21:32:22 | Error403 | my Linksys card (5v) works in the 5v slot, but it causes kernel panics after too much usage |
| 21:32:31 | Error403 | it doesn't seem to be causing any damage |
| 21:32:42 | BZFlag | Error403: no, but the kernel thinks it is applying 3v. |
| 21:32:55 | Error403 | So the kernel can control the hardware? |
| 21:33:16 | BZFlag | so the card driver might try something if it thinks it's really 3v |
| 21:34:33 | Error403 | hmm |
| 21:37:16 | Error403 | BZFlag: I'm not sure if I can honestly say that it's not hardware related |
| 21:37:37 | Error403 | BZFlag: I still randomly get CRC errors when the kernel decompresses itself |
| 21:37:50 | Error403 | BZFlag: But those CRC errors are usually after I have a kernel panic |
| 21:42:54 | BZFlag | odd. |
| 21:43:01 | Error403 | BZFlag: Quite honesly, I'm a userspace programmer, but I'd be willing to look at some kernel source for the first time in my life if you could point me in the right direction |
| 21:43:09 | Error403 | changes are I'd do more harm than good though |
| 21:43:52 | BZFlag | see ken's comments on http://TuxScreen.net/wiki/view/PCMCIA-5V |
| 21:44:16 | Error403 | gah |
| 21:44:28 | Error403 | BZFlag: Why is it that your site is the only site that has DNS issues? ;) |
| 21:44:57 | scanline | BZFlag: do you know if the kernel bug where wheaties makes the ucb1200 sound crackle has been fixed yet? |
| 21:45:07 | Error403 | BZFlag: That's not a good thing afaik |
| 21:45:58 | Error403 | nevermind |
| 21:47:07 | Error403 | BZFlag: Do I need a diode? |
| 21:48:05 | BZFlag | Error403: stinking cisco router |
| 21:48:44 | BZFlag | Error403: you don't need a diode. it's only for making dual voltage slots, and not even the best way to do that. |
| 21:49:05 | Error403 | BZFlag: So technically I did everything right |
| 21:49:23 | Error403 | and it's kinda disappointing that I get kernel panics and general instability because I shouldn't |
| 21:56:32 | Error403 | BZFlag: I'm not sure if it's the kernel, but it seems it might be because I get warnings that say "CS requested 0v, still sent 3.3v" |
| 22:08:27 | Error403 | This would be much easier if I just went and bought a 3.3v card for crying out loud |
| 22:09:22 | Error403 | BZFlag: If I got a 3.3v card, would I have to connect Pin 1->Pin 5, and disconnect Pin 5 from the 5v connection? |
| 22:24:54 | Error403 | ehem |
| 22:24:57 | Error403 | BZFlag: Ping? :/ |
| 22:46:24 | Error403 | TomW: hi |
| 22:46:35 | TomW | hello |
| 22:49:44 | scanline | Is it possible to reflash the kernel and jffs over ethernet? My null modem cable is a little bit too short :( |
| 22:52:00 | Error403 | TomW: http://www.kdedevelopers.net/~error403/tuxscreen |
| 22:52:12 | Error403 | TomW: If you'd care to look at my soltering job :) |
| 22:52:46 | TomW | scanline: There was some discussion of that on the mailing list. Something about the /dev/mtd? being the way to program the flash areas from a running kernel. |
| 22:52:50 | BZFlag | Error403: yes, but not in that order. ;-) disconnect first. |
| 22:53:04 | scanline | TomW: ok |
| 22:53:20 | Error403 | BZFlag: heh, of course :) |
| 22:53:22 | TomW | scanline: look in the mail archives. |
| 22:53:35 | TomW | scanline: ... if there are any ;-) |
| 22:53:36 | Error403 | BZFlag: http://www.kdedevelopers.net/~error403/tuxscreen shows my connections as they are now. Sorry for the bad angles :( |
| 22:54:17 | Error403 | BZFlag: I found some more comments on how to modify the kernel to support 5v, but do you think it would be possible for you to do it for me and send me a new kernel? :/ |
| 22:54:33 | Error403 | Or should I try my cross compiler again? :} |
| 22:58:52 | scanline | is away: eating a little pseudomeat with my hot sauce |
| 23:01:26 | Error403 | ugh, wiki makes finding stuff an adventure of its own |
| 23:07:29 | BZFlag | scanline: mtd0 is the bootloader, mtd1 is the kernel mtd2 is the rootfs |
| 23:07:47 | Error403 | BZFlag: Where is that site for the cross compilers again? :/ |
| 23:07:54 | BZFlag | scanline: be sure to "mount -o remount,ro /" before trying to reflash mtd2 from user space. |
| 23:08:30 | BZFlag | and cycle power right after. (or sysctl reset) |
| 23:08:51 | BZFlag | http://TuxScreen.net/wiki/view/ToolChain |
| 23:09:24 | BZFlag | Error403: I might do a kernel for you, but I'm swamped at the moment. ask on -dev |
| 23:09:46 | Error403 | I will do it myself |
| 23:10:21 | Error403 | I wonder if the Lineo cross compiler will work okay? |
| 23:10:37 | Error403 | I have access to that, and I know it works for other arm cross compiles |
| 23:10:43 | BZFlag | Error403: it should, yes. |
| 23:11:34 | Error403 | k |
| 23:14:59 | Error403 | hmm |
| 23:15:07 | Error403 | I only have the ones from Sharp |
| 23:15:13 | Error403 | I'm betting those will work |
| 23:19:11 | scanline | is back (gone 00:20:19) |
| 23:19:17 | scanline | BZFlag: thanks |
| 23:58:26 | BZFlag | Error403: afaik those are the ones from Lineo. ;-) |
