| 00:47:21 | Russ | downloading kernel.... |
| 00:48:27 | Russ | Linux version 2.4.6-rmk2-np1 (russ@russ) (gcc version 2.95.2 19991024 (release)) #2 Sun Jul 22 17:45:18 MST 2001 |
| 00:48:32 | Russ | Processor: Intel StrongARM-1100 revision 9 |
| 00:48:36 | Russ | Architecture: SHANNON |
| 00:48:50 | Russ | SA1100 flash: probing 32-bit flash bus |
| 00:48:55 | Russ | SA1100 flash: Found 2 x16 devices at 0x0 in 32-bit mode |
| 00:49:01 | Russ | Amd/Fujitsu Extended Query Table v1.0 at 0x004 |
| 00:49:05 | Russ | number of CFI chips: 1 |
| 00:49:12 | Russ | 0: offset=0x0,size=0x8000,blocks=1 |
| 00:49:15 | Russ | 1: offset=0x8000,size=0x4000,blocks=2 |
| 00:49:15 | Russ | 2: offset=0x10000,size=0x10000,blocks=1 |
| 00:49:15 | Russ | 3: offset=0x20000,size=0x20000,blocks=31 |
| 00:50:00 | Russ | Unable to handle kernel paging request at virtual address c0400000 |
| 00:50:11 | Russ | hmm...I think the ramdisk is at a bad address |
| 01:36:14 | Russ | Memory: 4MB 4MB 4MB 4MB = 16MB total |
| 05:48:56 | Russ | hey Tangent |
| 05:53:42 | Tangent | Hi Russ |
| 05:53:57 | Tangent | Russ : Any progress? |
| 05:54:00 | Russ | blob is fully tuxscreenized |
| 05:54:11 | Russ | there were a number of problems |
| 05:54:51 | Russ | the kernel and stack were coliding |
| 05:55:21 | Russ | and also the ram is mapped in 4M sections, so blob was copying stuff into the blank spaces |
| 05:55:27 | Russ | I also added AMD flash support |
| 05:55:47 | Russ | I have kernel patches up as well, but something about the ramdisk isn't working |
| 05:56:22 | Russ | as well as low level serial stuff (I never see Uncompressing linux....) only the regular kernel messages |
| 05:56:25 | Tangent | Russ : Still... that's very good progress... |
| 05:56:33 | Russ | Linux version 2.4.6-rmk2-np1 (russ@russ) (gcc version 2.95.2 19991024 (release)) #16 Sun Jul 22 23:48:07 MST 2001 |
| 05:56:33 | Russ | Processor: Intel StrongARM-1100 revision 9 |
| 05:56:33 | Russ | Architecture: SHANNON |
| 05:56:38 | Tangent | Russ : You were working hard whilst I was sleeping :) |
| 05:56:58 | Russ | so right now its getting stuck where is gunzips the ramdisk |
| 05:57:26 | Russ | there is a flashing from sboot, so if you want to go to blob, you may not need jtag hardware |
| 05:57:48 | Tangent | Excellent... That's exactly what I want |
| 05:58:05 | Russ | erikm has a 2.95.2 cross compiler on the lart pages |
| 05:59:56 | Tangent | Is the flashing from Sboot procedure documented yet? I was trying to work out how to use it last night |
| 06:00:46 | Russ | it is, but it uses bizzare windows tools |
| 06:01:00 | Russ | I don't know if they are necessary |
| 06:01:13 | Tangent | Is that the procedure which refers to *the* files? |
| 06:01:22 | Russ | dunno |
| 06:03:31 | Tangent | I found some more helpful sboot docs here... http://www.eclipse.net/~shaggy/shannon.html |
| 06:03:56 | Tangent | Looks like the guy who was writing them changed jobs though.. I found a copy of his CV online too |
| 06:03:57 | Russ | http://www.mailgate.org/comp/comp.os.inferno/msg00476.html |
| 06:04:12 | Russ | "the files" |
| 06:04:21 | Tangent | Yeah.. in step 3 and step 7 |
| 06:04:27 | Tangent | Which files damnit :) |
| 06:04:39 | Russ | I think maybe {n} |
| 06:05:07 | Tangent | But my main problem with that procedure is that I lack armsd |
| 06:06:14 | Russ | you are close to aleph1 |
| 06:07:18 | Tangent | Nod.... wish I had a jtagger to fix things when I undoubtedly mess them up |
| 06:07:39 | Russ | ask wookey how much you can get a dongle for |
| 06:08:16 | Tangent | Who's wookey? |
| 06:08:29 | Russ | guy at aleph1 |
| 06:08:36 | Russ | wow, they have quite the building |
| 06:08:41 | Russ | http://www.aleph1.co.uk/Company/Contact.html |
| 06:08:47 | Russ | "The Old Courthouse" |
| 06:08:51 | Tangent | does some cleaning |
| 07:21:09 | Tangent | finished cleaning... 1 hour... must have been a mess |
| 09:33:09 | JALH | moo |
| 12:14:44 | bworth | Tangent: how are your tuxscreens? |
| 14:50:25 | nikos | is away: Errands |
| 15:41:41 | nikos | is back |
| 17:02:28 | Tangent | bworth : I've only unpacked one of them, but it's a very nice unit |
| 17:03:01 | Tangent | bworth : Inferno is actually quite nice... It's a lot more than I was expecting.. I though the units just had a bootloader on... I didn't realise that they are fully functional |
| 17:12:35 | bworth | Tangent: yeah, i checked out Carl's tuxscreen when I was down there over Independence Day. He still has the Inferno software on his. It sure looks like ALOT of potential for $99US |
| 17:13:04 | bworth | I'll be ordering mine as soon as i have the extra money. |
| 17:14:34 | bworth | I suppose you have a windows box to test anything i may come up with on the usb install? Do you have green's e-mail address? |
| 17:17:39 | BZFlag | bworth: usb install for what? ipaq? |
| 17:21:28 | bworth | BZFlag: actually usbNet between ipaq and Windows host |
| 17:21:37 | bworth | (not install) |
| 17:22:55 | bworth | BZFlag: trying to use the Ipaq with existing EZ-Link windows drivers (if that doesn't work i'm going to try to write new windows drivers) |
| 17:23:28 | BZFlag | bworth: cool! post to the wiki if/when it works. ;-) |
| 17:23:49 | bworth | i will - wish me luck |
| 17:24:08 | bworth | BZFlag: what is the status of familiar on the tuxscreen? |
| 17:25:51 | BZFlag | bworth: slow progress being made on the bootloader still. once the kernel boots most everything should be working cept sound and the phone features. then we'll need to do driver work on boh of those. |
| 17:26:42 | bworth | BZFlag: sounds good - i'll be ordering mine soon :) |
| 17:27:35 | nikos | BZFlag: Touchscreen/LCD will be working? |
| 17:28:44 | BZFlag | nikos: yes, I have working code to pull the driver stuff from. |
| 17:28:54 | nikos | BZFlag: Excellent. |
| 17:29:10 | BZFlag | the same panel/ts is used on the "graphics client" board. |
| 17:29:14 | BZFlag | we have a few here. |
| 17:40:07 | Tangent | bworth : I have both the windows box, and green's email address |
| 17:40:57 | Tangent | BZFlag : Russ got a kernel loading now, with working serial support... but it has initrd problems at the moment |
| 17:44:36 | BZFlag | Tangent: on ipaq or shannon? |
| 17:47:31 | Tangent | BZFlag : shannon |
| 17:47:42 | Tangent | BZFlag : He's started a CVS repositary too |
| 17:48:08 | Tangent | BZFlag : I just need a procedure for getting his blob on to my tuxscreen without a jtagger |
| 17:48:57 | Tangent | Tho sboot is rather fun... particularly the Test Touchscreen function |
| 18:10:34 | bworth | is back - (stupid tech hit the wrong circuit breaker) |
| 18:52:37 | Russ|werk | BZFlag? |
| 19:10:04 | BZFlag | Russ: hit me! |
| 19:10:24 | Tangent | BZFlag : He left again |
| 19:10:55 | Tangent | BZFlag I'm somewhat confused by the inferno upgrade docs... |
| 19:12:32 | Tangent | BZFlag : It refers to *the* files in steps 3 and 7, and I'm not certain which files it means... Also, where can I get hold of armsd |
| 19:12:33 | BZFlag | can I help? |
| 19:13:13 | Tangent | BZFlag : Tho if I can skip straight to BLOB, then I'd rather do that... but I guess you need to talk to russ about that |
| 19:14:22 | Tangent | BZFlag : BTW.. i take it that you found this before.. I couldn't find it linked from tuxscreen.net, but it was very useful... http://www.eclipse.net/~shaggy/shannon.html |
| 19:14:29 | BZFlag | Tangent: got dled inferno up? |
| 19:14:45 | Tangent | BZFlag : Yeah.. got the file down |
| 19:14:47 | BZFlag | Tangent: it's on the links page in th eiki. |
| 19:15:06 | Tangent | BZFlag : OK.. I've been having stupidity problkems all day anyhow ;) |
| 19:15:24 | BZFlag | meant the wiki... |
| 19:24:27 | Tangent | BZFlag : Any idea where I can get armsd? |
| 19:26:43 | BZFlag | esc -> ctrl-a will get your device into armsd mode. |
| 19:26:53 | BZFlag | then I use the DLed inferno to talk to it. |
| 19:27:05 | BZFlag | check, uh... |
| 19:27:55 | BZFlag | http://erire.com/shannon/upgrade.html but it looks like it's down again... |
| 19:28:12 | Tangent | BZFlag : http://www.mailgate.org/comp/comp.os.inferno/msg00476.html |
| 19:28:18 | Tangent | Same thing |
| 19:28:35 | Tangent | isn't it? |
| 19:28:44 | Tangent | I got down the inferno dev kit thingy |
| 19:30:50 | BZFlag | mostly, but the erire one uses inferno which you can get, intead of armsd which I don't have. |
| 19:31:12 | Tangent | Ah.. I must have never seen the erire one then |
| 19:31:28 | BZFlag | then start inferno and do the steps on http://TuxScreen.net/wiki/view/Main/InfernoRemote |
| 19:31:32 | Tangent | I've got inferno down anyhow... I just don't know what to do with it |
| 19:32:04 | Tangent | Where do I put linuxemu.gz? |
| 19:32:29 | Tangent | Hmm.. nowhere... 404 not found |
| 19:33:14 | BZFlag | the newer inferno may just work for you. I needed that file for 2.4 kernel support. |
| 19:33:18 | BZFlag | can you start the emu ? |
| 19:33:26 | Tangent | Yep |
| 19:33:41 | BZFlag | ok, then you don't need the tar. feel free to update the wiki page. |
| 19:35:35 | Tangent | BZFlag : BTW.. I'm doing this on a windows box, as that's what the docs said it worked on |
| 19:35:46 | Tangent | That may be why I don't need linuxemu.gz |
| 19:42:48 | Tangent | Hmm... ok.. so with the next stages... |
| 19:43:08 | Tangent | If I type the bind as it appears on the page, it gives me a parse error |
| 19:43:48 | Tangent | No,.. if it type it correctly, it's fine |
| 19:44:09 | Tangent | Oooh.. they're talking to one another :) |
| 19:45:02 | Tangent | OK.. so what next? |
| 19:49:32 | BZFlag | now you just need to copy over a file to the "all" flash partition. but be SURE to get the right command first. |
| 19:49:43 | BZFlag | else you will brick your phone. |
| 19:49:51 | Tangent | Any clues as to the command? |
| 19:50:08 | Tangent | Bricking one is OK.. I got a spare :) |
| 19:50:19 | Tangent | After that I have to make the jtagger |
| 19:50:24 | BZFlag | The erire page had the exact command, which I tested, but now it's down. I need to copy shaggy page and that page into the wiki. =( |
| 19:50:37 | BZFlag | and if you add jtag, you can get back. |
| 19:51:02 | Tangent | It's a one chip board.. I can always solder it together on a bit of stripboard if I have to |
| 19:51:34 | Tangent | And it's not hard to get hold of 7400 series logic either |
| 19:53:37 | Tangent | Hmm.. erire.com is up, but rejecting http connections... |
| 19:53:48 | Tangent | I guess it's an IIS server then |
| 20:06:06 | BZFlag | heh |
| 20:13:28 | Tangent | BZFlag : I don't suppose you have a copy of the doc in your web browser's cache still do you? |
| 20:16:43 | Tangent | BZFlag : Do you have this one too? http://www.ishiboo.com/~nirva/Projects/hardware/phone/ |
| 20:17:11 | Tangent | Yeah.. you do |
| 20:31:59 | Tangent | I think I may have just worked out Russ's initrd problem |
| 20:32:12 | Tangent | I may have met the same problem with doing the bootfromCE for the iPAQ |
| 20:32:34 | Tangent | There's a couple of lines in the kernel that stop you from having rootfs = initrd |
| 20:32:41 | Tangent | I know the patch for this too |
| 20:33:52 | jacques_gone | yo yo |
| 20:33:59 | Tangent | jacques_gone : Hi |
| 20:34:27 | jacques_work | hi Tangent :-) |
| 20:34:46 | nikos | is away: meeting... |
| 20:34:46 | Tangent | jacques_work : Have I missed the conf call? |
| 20:36:03 | jacques_work | Tangent: conf call is at 2pm eastern == 11am my time == 3.5 hours ago :-( |
| 20:36:10 | jacques_work | Tangent: I missed it too - forgot |
| 20:36:30 | Tangent | Ah.. I was wondering... I though it would be in about 20 mins time up until about 10 mins ago... |
| 20:36:49 | Tangent | I wouldn't have been able to make it 3.5 hours ago |
| 20:45:07 | Tangent | http://www.vitanuova.com/inferno/man/10/sboot.html |
| 20:46:50 | nikos | is back |
| 20:47:16 | sgodsell | Hello Everyone |
| 20:47:21 | Tangent | Hi sgodsell |
| 20:47:38 | sgodsell | Hello Tangent |
| 20:49:09 | sgodsell | Okay guys this might be a stupid question, but where do you hook up the jtag on the tuxscreen (contacts). |
| 20:50:02 | sgodsell | Is there a page that shows this? |
| 20:50:56 | sgodsell | I just got my tuxscreens today |
| 20:53:57 | sgodsell | Whoooa |
| 20:54:02 | sgodsell | Hello guys |
| 20:54:09 | Tangent | sgodsell : Hi again |
| 20:54:15 | sgodsell | BZFlag, did you get my message |
| 20:54:16 | Tangent | sgodsell : Just a small server split |
| 20:54:23 | sgodsell | Hi Tangent |
| 20:54:28 | sgodsell | Ohhhh |
| 20:54:41 | sgodsell | I just received my 2 tuxscreens today |
| 20:54:58 | sgodsell | Tangent: do you have linux on yours? |
| 20:55:10 | Tangent | sgodsell : No.. not yet... |
| 20:55:16 | sgodsell | Hmmmm |
| 20:55:20 | Tangent | sgodsell : Russ has a nearly booting kernel now |
| 20:55:29 | sgodsell | Oh |
| 20:55:34 | Tangent | sgodsell : It boots, but has initrd problems.. but I think I know how to fix that |
| 20:55:46 | sgodsell | Is Russ listening right now |
| 20:55:54 | Tangent | sgodsell : I don't think so... |
| 20:56:07 | Tangent | sgodsell : I think he's at work.. he appeared briefly as Russ|Werk |
| 20:56:11 | sgodsell | Russ: Are you using a jtag on the tuxscreen? |
| 20:56:18 | Tangent | sgodsell : He is |
| 20:57:03 | sgodsell | I would like to know where you hook up the jtag on the tuxscreen |
| 20:57:25 | sgodsell | Whick contacts? |
| 20:57:35 | sgodsell | Do you know Tangent? |
| 20:58:10 | Tangent | sgodsell : Just searching for the page |
| 20:58:21 | sgodsell | Oh, Thanks |
| 20:58:45 | Tangent | http://www.tuxscreen.net/wiki/view//FlashUnlock |
| 20:59:09 | Tangent | http://www.tuxscreen.net/wiki/view/Main/jtag |
| 21:01:57 | sgodsell | Hmmm, the first one tells you which pins are used to unlock the flash memory. The second URL tells you how to build one, and where you can get jflash, but not the pins used for the jtag. Unless I am blind or stupid (probably the last option is true :) |
| 21:02:23 | Tangent | sgodsell : You need to solder on the right angle connector... |
| 21:02:30 | Tangent | sgodsell : That's where the jtag pins are |
| 21:03:31 | sgodsell | So looking at the screen shot of where the sodim module is, that is where you put the jtag? |
| 21:03:54 | Tangent | sgodsell : I don't know.. I don't have jtagger etc.. haven't removed screws |
| 21:04:06 | Tangent | sgodsell : I only got my phones on saturday |
| 21:04:09 | sgodsell | Hmmm |
| 21:04:18 | Tangent | I think I'm beginning to understand sboot though |
| 21:04:22 | sgodsell | The are pretty cool. |
| 21:04:34 | Tangent | If my theory is correct, I'm currently backing up my inferno image to my local hard disk |
| 21:04:41 | sgodsell | The boot loader that comes with the tuxscreen |
| 21:04:48 | Tangent | sgodsell : Yep |
| 21:05:02 | sgodsell | Using a flash card |
| 21:05:07 | sgodsell | to backup? |
| 21:05:08 | Tangent | sgodsell : To gain access, you can either do some special stuff on the tuxscreen keyboard when it boots up |
| 21:05:24 | sgodsell | esc, ctrl-d, ctrl-p |
| 21:05:30 | Tangent | sgodsell : Or, you can install the inferno dev environment on a Windows box, and control it remotely |
| 21:05:56 | sgodsell | So did you buy inferno? |
| 21:06:00 | sgodsell | os |
| 21:06:06 | Tangent | sgodsell : No.. just downloaded the free version |
| 21:06:12 | sgodsell | Ohhh |
| 21:06:21 | BZFlag | jtag connectors are next to the pcmcia slot on the back. you need to open the box to solder on those. |
| 21:06:34 | BZFlag | the 12v connector is under the sodimm |
| 21:07:02 | sgodsell | Are they clearly marked |
| 21:07:13 | sgodsell | Also did you get the funds BZFlag? |
| 21:07:41 | BZFlag | sgodsell: got the funds. they are not marked at all. see: |
| 21:07:56 | sgodsell | see? |
| 21:08:16 | BZFlag | http://TuxScreen.net/wiki/view/Main/FlashUnlock for 12v connect info. |
| 21:08:36 | sgodsell | Yes I saw that URL before? |
| 21:08:53 | sgodsell | That is to unlock the flash memory, correct? |
| 21:09:03 | BZFlag | the 12v pins are labeled in the pic: http://TuxScreen.net/img/flashprotectpins.jpg |
| 21:09:07 | BZFlag | yes, to unlock the flash. |
| 21:09:10 | Tangent | BZFlag : With blob, is it possible to transfer the entire 4MB flash image over back to the PC, including blob itself? |
| 21:09:42 | BZFlag | Tangent: that will be easy from Linux on the device. |
| 21:09:52 | BZFlag | it's easy, but slow with jtag now. |
| 21:10:04 | Tangent | BZFlag : Well... I think we may be only hours away from that |
| 21:10:07 | BZFlag | it should also be possible from sboot over serial. |
| 21:10:23 | Tangent | BZFlag : If I'm right, I can load arbtrary images into flash with sboot |
| 21:11:05 | Tangent | So if you or russ can get a booting kernel+initrd, then I can flash with that... just as long as blob will let me reflash afterwards |
| 21:11:38 | BZFlag | Tangent: yes. once. |
| 21:11:53 | BZFlag | then blob later, right. |
| 21:12:02 | Tangent | Yeah.. blob later |
| 21:12:30 | BZFlag | that's the plan, so most folk will not need jtag. they will need to do the 12v unprotect though. |
| 21:12:57 | Tangent | BZFlag : I'm happy to try it if you can prepare me a 4MB blob image to replace the current stuff with |
| 21:13:17 | Tangent | Tho' I'd like to get a kernel on there too first |
| 21:13:44 | BZFlag | you can try the inferno update, but then you loose armsd type ability. Don't know how to flash whole images after the upgrade yet. |
| 21:14:03 | Tangent | Does it get rid of sboot? |
| 21:14:14 | Tangent | I'll not do the upgrade if it's going to loose stuff |
| 21:14:22 | BZFlag | no, there is a new sboot that speaks a different serial protocol. |
| 21:14:42 | Tangent | So it won't talk to the inferno stuff on my PC? |
| 21:14:47 | BZFlag | so the inferno link commands will be different, that's all. |
| 21:15:08 | BZFlag | I just don't know the new "magic" commands to get them to talk yet. |
| 21:19:04 | Tangent | BZFlag : Is that the styx stuff I've seen mentioned? |
| 21:28:52 | Tangent | echo b9600 >/dev/eia0ctl |
| 21:28:53 | Tangent | mount -A /dev/eia0 /n/rdbg |
| 21:28:59 | Tangent | http://www.vitanuova.com/inferno/man/10/styxmon.html |
| 21:34:17 | sgodsell | What a real bitch to get that board out !!!! |
| 21:34:45 | sgodsell | I almost broke it :( |
| 21:42:34 | sgodsell | Hello Russ |
| 21:43:12 | Tangent | Russ : Just the man |
| 21:43:25 | Tangent | Russ : I think I may know what your initrd problem is |
| 21:45:20 | Russ|werk | probably has to do with initrd being in the kernels path of uncompression |
| 21:45:45 | Tangent | Russ : There's a couple of lines in the kernel that prevent you from having rootfs=initrd |
| 21:46:22 | Russ|werk | Tangent: it stops at gunzip() |
| 21:46:40 | Russ|werk | something about gunzip()'ing the ramdisk causes things to stop |
| 21:46:54 | Tangent | Russ : How big is the ramdisk? |
| 21:49:14 | Russ|werk | the gzip'd file is 3M |
| 21:49:14 | Russ|werk | the ramdisk is 8M |
| 21:49:14 | Russ|werk | if you look at the patch in shannon.c, it shows all the memory setup |
| 21:49:14 | Tangent | Russ : Haven't downloaded kernel yet |
| 21:49:14 | Russ|werk | the patch provides all of shannon.c, so looking at the patch shows the file |
| 21:51:54 | Russ|werk | " I think the BGA |
| 21:51:55 | Russ|werk | packages are actually easier to hand solder then fine-pitched SM because as |
| 21:51:55 | Russ|werk | the spacing between the pads is much greater. |
| 21:51:55 | Russ|werk | " |
| 21:51:55 | Russ|werk | god help us all |
| 21:51:55 | Russ|werk | duhhh |
| 21:53:04 | BZFlag | Tangent: found the jtag header? |
| 21:53:16 | Tangent | BZFlag |
| 21:53:19 | Tangent | Not looking |
| 21:53:31 | Tangent | BZFlag : You want sgodsell |
| 21:53:33 | BZFlag | oh, sorry, it's sgodsell that's looking. |
| 21:53:38 | BZFlag | heh |
| 21:53:43 | Tangent | :) |
| 21:53:45 | BZFlag | sgodsell: you find them? |
| 21:53:49 | sgodsell | Yes |
| 21:54:05 | BZFlag | http://TuxScreen.net/img/mvc-627f.jpg |
| 21:54:08 | sgodsell | Well Russ is going to confirm |
| 21:54:21 | BZFlag | note that my current recommendation is to cut a hole in the back as per: |
| 21:54:29 | sgodsell | so it is j100 |
| 21:55:11 | BZFlag | note that my current recommendation is to cut a hole in the back as per: |
| 21:55:18 | sgodsell | Thanks BZflag |
| 21:55:21 | BZFlag | hmm... I guess I have not posted pics of that... |
| 21:55:32 | sgodsell | I didnt see any |
| 21:55:53 | sgodsell | Make sure you tell them it is J100 |
| 21:56:04 | BZFlag | ok |
| 21:56:56 | sgodsell | How long does it take to flash it using the jtag. Is it as fast as the iPAQ? |
| 21:57:45 | sgodsell | Well I know it is smaller amount of flash ram, but what I mean is it the same speed per second |
| 21:58:02 | sgodsell | like 600K |
| 21:58:36 | Russ|werk | I just ran mine through the ramdisk door |
| 21:58:46 | sgodsell | Oh, thanks Russ|werk BZFlag just sent me an image and it is labeled J100 |
| 21:58:56 | Russ|werk | jtag is no longer needed for very long now that blob flashes blob |
| 21:58:59 | sgodsell | Thanks again for your help Russ|werk |
| 21:59:26 | sgodsell | Hmmm |
| 22:02:12 | BZFlag | sgodsell: I just updated http://TuxScreen.net/wiki/view/Main/JTAG for ya. |
| 22:02:28 | sgodsell | Great! |
| 22:02:36 | Russ|werk | hopefully, someone will figure out a flashing blob from sboot procedure |
| 22:02:55 | BZFlag | I can flash 4M in < 2 hours with a holly dongle. no it's not very fast at present. |
| 22:03:08 | Russ|werk | BZFlag: now you don't need to |
| 22:03:29 | BZFlag | I suspect with other jtag equipment it could be < 15 minutes. but as Russ mentions, you don't need it anymore. ;-) |
| 22:04:26 | BZFlag | I will try Russ' new patches tonight as well as a non-jtag install and document that on the wiki. |
| 22:04:41 | BZFlag | I'll probably post the blob binary as well. |
| 22:04:56 | BZFlag | thanks Russ again... ;-) |
| 22:06:37 | Russ|werk | BZFlag: my stuff at work is around 30 minutes for 4M, but it could be about twice as fast |
| 22:14:00 | Russ|werk | unfortunately, I'm going out with some gf tonight, so I don't know if I'll get the ramdisk loading |
| 22:14:39 | Russ|werk | any news on whether or not the schematics are in the mail? |
| 22:15:32 | BZFlag | should be, but I have not seen em. I'll email him again. |
| 22:16:47 | Russ|werk | because making the ucb work will probably be easy, but making the sound come out of the phone will probably require switching something |
| 22:17:00 | Russ|werk | ie, off/speaker/handset |
| 22:19:53 | Tangent | goes to bed.. night all |
| 22:22:26 | sgodsell | I have to go guys, Thanks once again! |
