| 01:10.28 | *** join/#openmoko DocScrutinizer05 (~saturn@openmoko/engineers/joerg) |
| 05:09.10 | *** join/#openmoko FFY00 (~FFY00@archlinux/trusteduser/ffy00) |
| 05:37.26 | *** join/#openmoko DocScrutinizer05 (~saturn@openmoko/engineers/joerg) |
| 09:15.25 | *** join/#openmoko DocScrutinizer05 (~saturn@openmoko/engineers/joerg) |
| 10:58.01 | *** join/#openmoko pa4wdh (~pa4wdh@2001:980:8e2f:ace::63) |
| 13:42.55 | *** join/#openmoko mickeyl (~mickeyl@109.90.164.198) |
| 22:07.46 | *** join/#openmoko azonenberg (~azonenber@2603:3023:241:40f8:216:3eff:fe6c:95a2) |
| 22:08.17 | azonenberg | Hi folks... anybody here able to help out with getting a usb PID under the openmoko VID? |
| 22:14.44 | PaulFertser | azonenberg: hi. I think I can try but not right atm. Do you know there's also pid.codes? |
| 22:15.32 | azonenberg | This isnt super urgent, the project has been going on for a fair bit of time already |
| 22:15.42 | PaulFertser | FFY00: same about your request. |
| 22:15.46 | azonenberg | This is for my open hardware oscilloscope probes, we'll be using some custom USB PD commands to power them |
| 22:16.05 | PaulFertser | I need to check if I still can edit the wiki to add your new codes, but not right atm as it's sleep time here. |
| 22:16.27 | azonenberg | For now only one PID needed because this PID is for the bridge MCU from USB PD to the analog stuff, which should be basically the same for all probes |
| 22:16.41 | azonenberg | but probably best to reserve a few just in case i need them later |
| 22:16.48 | PaulFertser | I do not even remember by now what's the difference in requirements between openmoko and pid.codes... |
| 22:17.00 | PaulFertser | iirc one of them needed both firmware and hardware to be free. |
| 22:17.26 | azonenberg | Everything for this project is 3-clause BSD |
| 22:17.29 | azonenberg | so that's fine by me |
| 22:18.19 | azonenberg | https://www.github.com/azonenberg/starshipraider the next version of the AKL-AD1 is going to be the first user of the bridge but I'd put down "active oscilloscope probe" as the description for the PID |
| 22:18.56 | azonenberg | it's not too important because these devices are PD *only* and don't do much in the way of other USB stuff. They won't break if you plug them into a PC or something, but that isn't the intended usage scenario |
| 22:20.27 | PaulFertser | Looks like a cool project. |
| 22:20.45 | azonenberg | D+ and D- will be connected in case we need them but at least initial firmware isn't even going to enumerate :p |
| 22:20.53 | azonenberg | All i need is power and a few low level control messages to negotiate voltage etc |
| 22:54.45 | FFY00 | my friend found this github repo which seems to be the correct place to submit right now |
| 22:54.46 | FFY00 | https://github.com/openmoko/openmoko-usb-oui |
| 22:55.29 | FFY00 | the wiki still has the old process, by emailing, which does not seem to be active right now |
| 22:55.40 | FFY00 | I opened a PR https://github.com/openmoko/openmoko-usb-oui/pull/24 |