| 00:44.41 | *** join/#openjtag _julian_ (~quassel@hmbg-5f77d2d4.pool.mediaWays.net) |
| 04:38.50 | *** join/#openjtag Weaselweb (~quassel@2001:6f8:9e4:123:21a:92ff:fe5a:1409) |
| 07:18.15 | *** join/#openjtag toi (~peter@d54C2AA76.access.telenet.be) |
| 07:25.33 | *** join/#openjtag Rogan (~rogan@196-215-42-88.dynamic.isadsl.co.za) |
| 08:46.24 | *** join/#openjtag roxfan (dunno@91.180.121.233) |
| 08:55.52 | *** join/#openjtag _julian (~quassel@hmbg-5f77d288.pool.mediaWays.net) |
| 13:34.45 | *** join/#openjtag Rogan (~rogan@196-215-42-88.dynamic.isadsl.co.za) |
| 14:01.47 | *** join/#openjtag matt_hsu (~matt@118-168-197-129.dynamic.hinet.net) |
| 14:08.13 | *** join/#openjtag toi (~peter@d54C2AA76.access.telenet.be) |
| 14:34.25 | *** join/#openjtag roxfan (dunno@91.180.121.233) |
| 17:35.13 | *** join/#openjtag matt_hsu (~matt@118-168-197-129.dynamic.hinet.net) |
| 17:53.26 | *** join/#openjtag matt_hsu (~matt@118-168-197-129.dynamic.hinet.net) |
| 19:22.56 | *** join/#openjtag matt_hsu (~matt@118-168-197-129.dynamic.hinet.net) |
| 19:40.06 | *** join/#openjtag ecc (~ecc@pool-173-75-141-44.pitbpa.fios.verizon.net) |
| 19:47.46 | ecc | I'm trying to use openocd to debug a kirkwood (feroceon) board. I've seen conflicting suggestions about whether or not to connect the SRST line. Any pointers on how to set this up the right way? |
| 19:49.41 | ecc | (I should say that I'm not very knowledgable about hardware -- I've been "forced" into it to try to debug some low-level u-boot and linux issues.) |
| 19:52.32 | Rogan | I would expect that you would need to connect SRST |
| 19:52.44 | Rogan | in order to allow the JTAG adapter to reset your board |
| 19:52.59 | Rogan | do you also have nTRST? |
| 19:56.13 | ecc | Yes, both nTRST and nSRST. It mostly works with just nTRST connected (even though the openocd "reset_config" is "trst_and_srst", which I don't understand either.) |
| 19:58.37 | Rogan | well, if you have only nTRST connected, you should set "reset nrst_only", I think |
| 20:01.34 | ecc | Well the "mostly works" part is that has trouble halting the processor reliably. Sometimes it works, sometimes it halts in Thumb mode, sometimes it times out ... I was hoping that if I connected nSRST also, and configured openocd correctly, that would go away. But how to configure openocd "from scratch" in a systematic, rather than trial-and-error, way? |
| 20:06.04 | *** join/#openjtag Openfree` (~Openfreer@116.228.88.131) |
| 20:10.49 | Rogan | ecc: well, if you connect SRST as well as nTRST, then you should configure "reset_config trst_and_srst" |
| 20:11.07 | Rogan | at least, that is my understanding of it |
| 22:27.51 | *** join/#openjtag flyhorse|linux (~flyhorse|@183.22.233.208) |