| 00:02.07 | *** join/#openjtag ali_as (~ali_as@ambix.plus.com) |
| 00:22.18 | *** join/#openjtag lool (~lool@debian/developer/lool) |
| 01:26.13 | *** join/#openjtag _julian_ (~quassel@dslc-082-083-155-069.pools.arcor-ip.net) |
| 03:51.30 | *** join/#openjtag [1]ali_as (~ali_as@ambix.plus.com) |
| 03:51.34 | *** join/#openjtag nslu2-log_ (~nslu2-log@limax.nslu2-linux.org) |
| 06:01.38 | *** join/#openjtag pytey (~pytey@howler.blatero.com) |
| 06:03.25 | *** join/#openjtag Weaselweb (~alex@178-25-116-20-dynip.superkabel.de) |
| 06:19.45 | *** join/#openjtag pytey (~pytey@howler.blatero.com) |
| 08:58.02 | *** join/#openjtag matthsu (~matt@61-30-10-70.static.tfn.net.tw) |
| 10:09.23 | *** join/#openjtag pirho (debian-tor@gateway/tor-sasl/pirho) |
| 10:09.37 | *** part/#openjtag pirho (debian-tor@gateway/tor-sasl/pirho) |
| 10:33.31 | *** join/#openjtag Weaselweb (~alex@178-25-116-20-dynip.superkabel.de) |
| 10:40.25 | *** join/#openjtag pirho (debian-tor@gateway/tor-sasl/pirho) |
| 10:40.47 | *** part/#openjtag pirho (debian-tor@gateway/tor-sasl/pirho) |
| 11:04.35 | *** join/#openjtag i__ (~none@unaffiliated/i--/x-3618442) |
| 11:51.20 | *** join/#openjtag [1]ali_as (~ali_as@unaffiliated/ali-as/x-9346880) |
| 12:14.11 | *** join/#openjtag flyhorse|linux (~flyhorse|@121.13.37.205) |
| 13:05.25 | *** join/#openjtag Weaselweb (~alex@178-25-116-20-dynip.superkabel.de) |
| 14:52.59 | *** join/#openjtag roxfan (dunno@91.180.75.103) |
| 15:03.14 | *** join/#openjtag cjameshuff2 (~cjameshuf@atterotech.com) |
| 15:07.12 | *** join/#openjtag ferar (~ferar@64.254.252.178) |
| 15:12.27 | ferar | hi, when I load my vmlinux to SDRAM "tftp 30_000_000 vmlinux" and then after loading I do go 30_000_000 (nothing happens!). However If I write the vmlinux after loading to NAND (i.e., nand write.i 30000000 40000 1F1F800), reset the board and let u-boot load that vmlinux all works fine! |
| 15:13.04 | ferar | how can I launch vmlinux from specific SDRAM address? |
| 15:16.47 | Weaselweb | ferar: i hope you dont type 30_000_000 with underscores |
| 15:16.58 | ferar | no of course :/ |
| 15:17.56 | Weaselweb | is there a specific reason you use go instead of bootm? |
| 15:18.06 | ferar | no |
| 15:18.20 | Weaselweb | but this seem be more a problem of u-boot itself, feel free to join #u-boot |
| 15:19.10 | ferar | ok thanks, let me check with them |
| 15:56.40 | *** join/#openjtag Weaselweb (~quassel@77-64-189-43.dynamic.primacom.net) |
| 16:18.43 | *** join/#openjtag nslu2-log (~nslu2-log@limax.nslu2-linux.org) |
| 16:21.52 | ferar | MMU=enabled, that means virtual memory addressing is on correct? |
| 16:48.27 | wookey | yes |
| 17:14.29 | ferar | wooky: fine, is there is an instruction in telnet openocd session to like show current memory map configuration? |
| 17:29.33 | i__ | ferar: mdb |
| 17:45.52 | *** join/#openjtag toi (~toi@d54C2AA76.access.telenet.be) |
| 20:48.45 | *** join/#openjtag cjhuff (~cjameshuf@atterotech.com) |
| 22:08.42 | *** join/#openjtag PaulFert` (~PaulFerts@aein-1-pt.tunnel.tserv6.fra1.ipv6.he.net) |