| 01:29.05 | *** join/#openjtag _julian (~quassel@dslc-082-083-150-064.pools.arcor-ip.net) |
| 02:48.14 | *** join/#openjtag nslu2-log (~nslu2-log@limax.nslu2-linux.org) |
| 05:57.32 | *** join/#openjtag Weaselweb (~quassel@77-64-189-43.dynamic.primacom.net) |
| 06:03.45 | *** join/#openjtag pytey (~pytey@howler.blatero.com) |
| 08:29.24 | *** join/#openjtag pytey (~pytey@howler.blatero.com) |
| 10:20.54 | *** join/#openjtag pirho (debian-tor@gateway/tor-sasl/pirho) |
| 10:21.07 | *** part/#openjtag pirho (debian-tor@gateway/tor-sasl/pirho) |
| 10:56.52 | *** join/#openjtag ali_as (~ali_as@ambix.plus.com) |
| 13:00.20 | *** join/#openjtag KotH (~attila@lou-outside.kinali.ch) |
| 13:00.30 | KotH | good afternoon |
| 14:26.51 | *** join/#openjtag ferar (~ferar@64.254.252.178) |
| 14:28.10 | ferar | <PROTECTED> |
| 14:30.04 | Weaselweb | ferar: reset command does not work? |
| 14:30.19 | ferar | no |
| 14:30.57 | Weaselweb | how do you know? I'm asking to eliminate some fallpits |
| 14:31.44 | ferar | I can on serial console output that u-boot loads then the linux kernel starts |
| 14:31.53 | ferar | I can issue halt, that works |
| 14:32.07 | ferar | that will freeze the console output |
| 14:32.48 | Weaselweb | which board are you using? which JTAG adapter? |
| 14:33.58 | ferar | http://gist.github.com/403830 |
| 14:35.28 | ferar | I have attached my test configuration file: I launch the daemon by "openocd -d 2 -f openocd.cfg" |
| 14:37.30 | Weaselweb | i dont work with samsung boards, but i've used several at91 boards with amontec tiny wiggler where reset command works |
| 14:37.52 | Weaselweb | IIRC you need to make sure the SRST and TRST pins are connected |
| 14:38.16 | ferar | ok |
| 14:40.25 | ferar | in samsung documentation I can't see any reference to srst or trst pins! |
| 14:51.21 | *** join/#openjtag roxfan (dunno@91.180.87.154) |
| 14:52.35 | Weaselweb | you should check the schematics about ICE interface |
| 15:40.08 | *** join/#openjtag pirho (debian-tor@gateway/tor-sasl/pirho) |
| 15:41.04 | *** part/#openjtag pirho (debian-tor@gateway/tor-sasl/pirho) |
| 15:55.30 | *** join/#openjtag ferar (~ferar@64.254.252.178) |
| 15:57.12 | ferar | on samsung's product website I found a BSDL file for design S3C2450, does anyone think it is relevant to openocd.cfg ? |
| 17:59.52 | KotH | probably not |
| 18:00.04 | KotH | unless you want to do a boundary scan of the board |
| 18:00.47 | KotH | btw: SRST: system reset (the cpu reset line), TRST: jtag reset (the jtag subsystem reset line) |
| 19:05.59 | roxfan | openocd does not do boundary scan (except as svf player) |
| 20:31.41 | ferar | thanks |
| 20:32.46 | ferar | I fixed the reset issue (it was hardware) however now when I issue : reset halt (I get reset/run!) |
| 20:34.18 | ferar | http://gist.github.com/404200 |
| 21:28.06 | *** join/#openjtag ferar (~ferar@64.254.252.178) |
| 21:29.48 | ferar | reset halt works fine under j-link (windows) the 'r' command really halts the system at the very first, does that mean it is j-link driver issue rather than configuration issue? |