| 01:29.10 | *** join/#openslug caplink811-log (n=caplink8@dslb-088-073-063-232.pools.arcor-ip.net) |
| 03:43.38 | *** join/#openslug DrZimmerman (n=theo@80-218-43-146.dclient.hispeed.ch) |
| 04:10.00 | *** join/#openslug nSiclair73de (n=Sinclair@p57b48c75.dip0.t-ipconnect.de) |
| 05:20.46 | *** join/#openslug pleemans (n=peter@d51A5E76A.access.telenet.be) |
| 06:31.35 | *** join/#openslug pleemans (n=peter@d5152D19B.access.telenet.be) |
| 07:36.09 | *** join/#openslug nslu2-log (n=nslu2-lo@nslu2-linux/dyoung) |
| 07:36.14 | *** join/#openslug CieD (n=CieD@host86-142-254-85.range86-142.btcentralplus.com) |
| 09:59.57 | *** join/#openslug kolla (n=kolla@haugum.uninett.no) |
| 11:43.36 | *** join/#openslug kolla (n=kolla@haugum.uninett.no) |
| 14:27.22 | *** join/#openslug gerdi__ (n=gerdi@dslb-084-059-138-065.pools.arcor-ip.net) |
| 15:11.32 | *** join/#openslug gerdi__ (n=gerdi@dslb-084-059-139-107.pools.arcor-ip.net) |
| 16:19.14 | *** join/#openslug gerdi_ (n=gerdi@dslb-088-068-115-154.pools.arcor-ip.net) |
| 16:43.58 | *** join/#openslug pleemans (n=peter@d51A5E76A.access.telenet.be) |
| 18:55.35 | *** join/#openslug caplink811-log (n=caplink8@dslb-088-073-046-042.pools.arcor-ip.net) |
| 18:58.01 | *** join/#openslug Bitmaster (n=Bitmaste@c-d061e253.325-1-64736c12.cust.bredbandsbolaget.se) |
| 22:38.05 | kapookee | When one goes from wired to wireless ethernet on the slug, do you have to change anything other than /etc/network/interfaces? |
| 22:38.34 | kapookee | It runs fine if I bring up the wireless manually. When I change /etc/network/interfaces and reboot it hangs with.. |
| 22:38.38 | kapookee | ADDRCONF(NETDEV_UP): eth1: link is not ready |
| 22:38.58 | kapookee | according to dmesg. |
| 22:45.11 | mwester | kapookee: might be module loading issue; perhaps the necessary modules are not available or loaded at the time the system processes the /etc/network/interfaces file at boot. |
| 22:45.33 | mwester | Works ok for me (atheros wireless, slugosbe 4.4) |
| 22:46.11 | mwester | I did have to do an "ifup ath0" before I could "iwconfig" the interface at all, though. |
| 22:46.30 | mwester | (it even works with WPA!) |
| 22:49.22 | kapookee | Yea, but that's via the command line, right? What about getting it to start at boot? |
| 22:49.33 | kapookee | ..or am I missing something? |
| 22:51.41 | kapookee | oops, missed one of you lines. :-) I'll check the "module loading issue". Thanks. |
| 22:53.47 | mwester | The ifup was done via the "ifup" script that's run when /etc/network/interfaces is processed. I also start wpa_supplicant in that script to get wpa to work; I'm sure there's a better way, but that hack worked for me. |
| 23:18.09 | rwhitby | mwester: can you put the contents of your /etc/network/interfaces file on the wiki somewhere? |
| 23:19.59 | kapookee | That *would* be helpful! |
| 23:21.36 | rwhitby | I've done something similar, including bridging eth0 and wireless. I can add that stuff to the same page. |
| 23:21.56 | rwhitby | (I don't have it working at the moment, but I have drips and drabs of the configuration files lying around) |